• BP series electric pumps are used in sprinkler and flow irrigation systems, to extract water from lakes, rivers, tanks and for other industrial uses. • Maximum flow rate: 260 m³/h • Maximum pressure: 89 m • Maximum power: 40 hp • Maximum operating temperature: 120°C • Maximum rotation speed: 3450 rpm • Type of fluid handled: Clean water
  • Pumping clean water and chemically non-aggressive liquids, for residential use, irrigation, agriculture, automated distribution in medium-sized tanks.
  • Protection module for clean water and waste water equipment. Protection and monitoring of submersible pumps and agitators using an all-in-one device for measuring motor and bearing temperature, leakage, vibration and voltage measurement.
  • Submersible, vertical, single-stage, floodable and non-self-priming monobloc electric pumps, for installation in humid areas. They have a dilacerator (S), a free passage impeller (F) or a diagonal open channel (D), in a fixed and transportable version. Available in ATEX version, ideal for pumping raw, activated and digested sludge, dewatering and water extraction, drainage of rooms and surfaces subject to risk of flooding.
    • Maximum discharge diameter: 100mm
    • Maximum flow: 135 m³/h
    • Maximum pressure: 47m
    • Maximum operating temperature: 40°C
    • Maximum turning speed: 3500rpm
    • Type of fluid handled: Sludge
  • Electric pump with open impeller for a maximum passage of solids of 8 mm. Suitable for irrigation, agriculture and drainage systems. • Maximum flow rate: 40 m³/h • Maximum height: 18.7 m • Maximum power: 3 hp • Maximum liquid temperature: 70°C • Rotation speed: 3600 rpm • Type of fluid handled: Clean water
  • Vertical high-pressure, multi-cell centrifugal pump, monobloc design and segmented body, with suction and discharge flanges of identical nominal diameters in in-line arrangement. With KSB SuPremE, a magnetless synchronous reluctance motor (except: 0.55 kW / 0.75 kW 1500 rpm motor sizes are equipped with permanent magnets) with efficiency class IE4/IE5 according to IEC TS 60034-30 -2:2016, for use with speed regulation system of KSB PumpDrive 2 or PumpDrive 2 Eco models without rotor position sensors. The motor mounting points comply with EN 50347. The dimensions of the surrounding surface comply with DIN V 42673 (07-2011). Available in ATEX version.
  • Single-stage monobloc pumps for a wide range of applications, with shaft protection bushing and replaceable wear rings and a simple mechanical seal with low operational cost that does not require external cooling. Their construction is of the back pull-out type and they can be installed in a horizontal, vertical or inclined position. • Maximum discharge diameter: 6″ • Maximum flow rate: 550 m³/h • Maximum pressure: 140 m • Maximum operating temperature: 90°C • Maximum rotation speed: 3500 rpm • Type of fluid handled: Clean water
  • It is a highly versatile and efficient pumping device designed for a wide variety of applications in the field of engineering and industry. This pump stands out for its ability to handle liquids reliably and effectively, making it an essential tool in various areas.
  • Vertically sectioned horizontal multistage pumps, with suction casings sealed together by means of flat gaskets and externally by tie rods. Recommended for pumping clean liquids, free of suspended solids and not chemically and/or mechanically aggressive.
  • Compact, silent and easy to operate and maintain pumps, specially designed for pumping white water and non-chemically aggressive liquids in general industry applications, such as residential, irrigation, among others.
    • Maximum discharge diameter: 1"
    • Maximum flow: 15 m³/h
    • Maximum pressure: 46.2m
    • Maximum operating temperature: 70°C
    • Maximum turning speed: 3450rpm
    • Type of fluid handled: Clean water
  • Single-stage radially divided volute casing monobloc pumps. Suction and discharge in line horizontally or vertically. It has a closed impeller, replaceable wear rings and a simple mechanical seal according to EN 12756. Back-pull-out design. Wide range of applications.
  • Single-stage pumps with axially split spiral casing, with double suction radial rotor for horizontal and vertical installation. Horizontal drive installed, both on the left and direct sides of the pump (optional). Flanges meet DIN, EN or ASME requirements
  • Suitable for domestic installations, water supply, small gardening, increasing pressure in water supply networks. They ensure minimal hydraulic loss and, being designed and manufactured in Italy, are a guarantee of high quality. • Maximum flow rate: 8 m³/h • Maximum pressure: 59 m • Maximum power: 3 hp • Maximum operating temperature: 70°C • Maximum rotation speed: 3450 rpm • Type of fluid handled: Clean water
  • Single-stage or multistage submersible electric pump for deep wells, for vertical or horizontal installation, built entirely in stainless steel, for well diameters of 150 mm (6”) and larger. Technical data • Maximum flow rate: 80 m³/h • Maximum pressure: 420 m • Maximum operating temperature: 50°C • Maximum rotation speed: 3500 rpm • Type of fluid handled: Clean water
  • They are specialized systems designed to provide a reliable supply of high-pressure water in the event of a fire. These equipment play a critical role in the safety of commercial, industrial, and residential buildings by ensuring sufficient water is available to effectively fight fires.
  • High performance SAER equipment in terms of performance and efficiency. Ideal for recirculation and conditioning systems, water supply and pressurization groups. Different types of mechanical closures available, also for food grade use.
  • Submersible, vertical centrifugal pump, polypropylene monobloc with noryl impeller, IP 68, single-stage, with level control in single-phase version, immersion depth 2 m. includes 10 m of cable. Applications: Automatic drainage of buckets, wells, tanks and warehouses at risk of flooding, reduction of surface water levels, drainage, drainage of underground passages, extraction of water from rivers and reservoirs.
  • Submersible, vertical, double-chamber, cast iron centrifugal pump with stainless steel impeller, IP 68, single-stage, with level control, immersion depth 5 m. Includes 10m of cable.
    • Untreated wastewater
    • Activated sludge
    • Circulation and heating sludge
    • Raw mud and rotten silt
    • mixed water
  • Horizontal pump with radially split spiral casing in “back pull-out” design, with radial impeller, single-suction, single-stage, in accordance with DIN EN ISO 5199, measurements in accordance with DIN EN ISO 2858 complement the nominal diameters of DN25 and ≥DN200 , in a wide variety of materials and seals, also available with a wet shaft design and conical closing chamber. Available in ATEX version.
  • Horizontal centrifugal pumps with radially split cast casing with coupling in back-pull out design. Available with different types of impellers: unassailable, open and multi-channel. Recommended for pumping wastewater, chemical effluents, muddy and dense liquids, viscous liquids and liquids with suspended solids.
  • Single-stage horizontal pumps, horizontal single suction and vertical discharge. Design back-pull-back, allows maintenance and repair services to be carried out from the rear without affecting the alignment or fixing of the pipes. Dimensionally constructed according to DIN 24256 /ISO 2858 standard, and mechanically according to ANSI B 73.1 standard.
  • Multistage electric pumps with vertical axis, without self-priming, of minimum dimensions, ideal for lifting equipment with or without autoclave, irrigation system and other applications for which it is necessary to achieve high pressures.  
  • CL 95 Non-toxic, fully rewindable, oil-bath submersible motors, NEMA connection. Axial load: 3000 to 6500 N. Designed, manufactured and tested in SAER workshops, the CL series motors ensure high reliability. Made in Italy guarantees high quality standards. For temperatures up to 35°C. CLE 95 Non-toxic, fully rewindable, oil-bath submersible motors. The “E” version has been designed to offer a solution with a better quality-price ratio than the CL series: the only difference is a reduced axial load (1500 N in the CLE version compared to 3000 N for the CL series), but it is made from the same materials. Tested and extremely reliable motors as standard, which can be coupled to any submersible pump, not just SAER, thanks to the NEMA connection. For temperatures up to 25°C.
  • The device consists of two pressure sensors and a display that records the pump load and indicates any potential for optimising the pump's efficiency and availability. The device consists of two pressure sensors and a display panel. PumpMeter is fully equipped at the factory and is configured according to the respective pump. It is connected via an M12 connector and is ready for immediate use.
  • Fully automatic pressure equipment with 2 or 3 (MVP) / 4 (SVP) vertical high pressure pumps in two variable speed models. The MVP and SVP variable speed models have continuous speed regulation on each pump through the frequency converter in the pump for asynchronous motors (MVP) or the PumpDrive speed regulation system and the KSB SuPremE motor (SVP), for fully electronic control of the required supply pressure. Equipped with central fuse box.
  • Fully automatic pressure equipment with 2 or 3 (MVP) / 4 (SVP) vertical high pressure pumps in two variable speed models. The MVP and SVP variable speed models have continuous speed regulation on each pump through the frequency converter in the pump for asynchronous motors (MVP) or the PumpDrive speed regulation system and the KSB SuPremE motor (SVP), for fully electronic control of the required supply pressure. Equipped with central fuse box.
  • At Hidrosistemas' we work with highly qualified technical personnel in the manufacture of the various controls necessary to operate the equipment. With all the necessary protections. In addition, we use certified quality components and world-renowned brands to safeguard the equipment.
  • Designed to last, high efficiency three-phase asynchronous motor, encapsulated, rewindable, power range from 8.8 to 300 hp, water lubrication
    • Maximum operating power: 300HP
    • Turning speed: 3500rpm
  • Centrifugal pumps with segmented body and single suction, with one or multiple stages for vertical or horizontal installation. They have mixed hydraulic systems with reduced impeller diameters, driven by submersible motors. Ideal for general supply systems, among other applications. • Maximum flow: 1,010 m³/h • Maximum pressure: 460 m • Maximum operating temperature: 50°C • Maximum rotation speed: 3500 rpm • Type of fluid handled: Clean water
  • Stainless steel submersible pumps with noryl rotor for pumping drinking water in installations such as tubular and deep wells. They generate low noise levels and have an integrated check valve that ensures minimal pressure loss.
    • Maximum discharge diameter: 2"
    • Maximum flow: 27 m³/h
    • Maximum pressure: 400m
    • Maximum liquid temperature: 30°C
    • Type of fluid handled: Clean water

Title

Go to Top